Uses of Class
jmri.jmrix.can.CanMessage

Packages that use CanMessage

jmri.jmrix.can	Defines classes for interfacing to a CAN-based model railway control bus.
jmri.jmrix.can.adapters.gridconnect	Defines classes for communicating with the CAN network via hardware which uses the GridConnect format.
jmri.jmrix.can.adapters.gridconnect.canrs	Defines classes for interfacing to a MERG CAN-RS or CAN-USB adapter.
jmri.jmrix.can.adapters.lawicell	Defines classes for communicating with the CAN network via hardware which uses the Lawicell format
jmri.jmrix.can.adapters.loopback	Defines classes for simulating communication with a CAN network via loopback
jmri.jmrix.can.cbus	Defines classes for interfacing to a MERG CBUS network.
jmri.jmrix.can.cbus.swing.configtool
jmri.jmrix.can.cbus.swing.console	Defines classes for a console utility to interact with a MERG CBUS network
jmri.jmrix.can.cbus.swing.eventtable	Defines classes for implementing an event table to interact with a MERG CBUS network.
jmri.jmrix.can.cbus.swing.nodeconfig
jmri.jmrix.can.swing.monitor
jmri.jmrix.can.swing.send	Provide a tool for sending CAN packets.
jmri.jmrix.openlcb
jmri.jmrix.openlcb.swing.monitor
jmri.jmrix.openlcb.swing.send	Provide a tool for sending OpenLCB CAN packets.

Uses of CanMessage in jmri.jmrix.can

Methods in jmri.jmrix.can with parameters of type CanMessage

abstract AbstractMRMessage	AbstractCanTrafficController.encodeForHardware(CanMessage m)
void	CanListener.message(CanMessage m)
void	CanInterface.sendCanMessage(CanMessage m, CanListener l) Send a message through the interface.

Constructors in jmri.jmrix.can with parameters of type CanMessage

CanMessage(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.adapters.gridconnect

Methods in jmri.jmrix.can.adapters.gridconnect with parameters of type CanMessage

AbstractMRMessage	GcTrafficController.encodeForHardware(CanMessage m) Encode a CanMessage for the hardware
void	GcTrafficController.sendCanMessage(CanMessage m, CanListener reply) Forward a preformatted message to the actual interface.

Constructors in jmri.jmrix.can.adapters.gridconnect with parameters of type CanMessage

GridConnectMessage(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.adapters.gridconnect.canrs

Methods in jmri.jmrix.can.adapters.gridconnect.canrs with parameters of type CanMessage

AbstractMRMessage

MergTrafficController.encodeForHardware(CanMessage m) Encode a CanMessage for the hardware

Constructors in jmri.jmrix.can.adapters.gridconnect.canrs with parameters of type CanMessage

MergMessage(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.adapters.lawicell

Methods in jmri.jmrix.can.adapters.lawicell with parameters of type CanMessage

AbstractMRMessage	LawicellTrafficController.encodeForHardware(CanMessage m) Encode a CanMessage for the hardware
void	LawicellTrafficController.sendCanMessage(CanMessage m, CanListener reply) Forward a preformatted message to the actual interface.

Constructors in jmri.jmrix.can.adapters.lawicell with parameters of type CanMessage

Message(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.adapters.loopback

Methods in jmri.jmrix.can.adapters.loopback with parameters of type CanMessage

AbstractMRMessage	LoopbackTrafficController.encodeForHardware(CanMessage m) Encode a CanMessage for the hardware
void	LoopbackTrafficController.sendCanMessage(CanMessage m, CanListener reply) Forward a preformatted message to the actual interface.

Uses of CanMessage in jmri.jmrix.can.cbus

Methods in jmri.jmrix.can.cbus that return CanMessage

static CanMessage	CbusMessage.getBootCheck(int c) Microchip AN247 format message to send the checksum for comparison
static CanMessage	CbusMessage.getBootEntry(int nn) CBUS bootloader commands
static CanMessage	CbusMessage.getBootInitialise(int a) Microchip AN247 format message to initialise the bootloader and set the start address
static CanMessage	CbusMessage.getBootNop(int a) Microchip AN247 format NOP message to set address The CBUS bootloader uses extended ID frames
static CanMessage	CbusMessage.getBootReset() Microchip AN247 format message to reset and enter normal mode
static CanMessage	CbusMessage.getBootTest() Microchip AN247 format message to check if a module is in boot mode
static CanMessage	CbusMessage.getBootWriteData(int[] d) Microchip AN247 format message to write 8 bytes of data
static CanMessage	CbusMessage.getOpsModeWriteCV(int mAddress, boolean mLongAddr, int cv, int val) CBUS Ops mode programmer commands
static CanMessage	CbusMessage.getReadCV(int cv, int mode) CBUS programmer commands
static CanMessage	CbusMessage.getRequestTrackOff()
static CanMessage	CbusMessage.getRequestTrackOn() CBUS Power commands
static CanMessage	CbusMessage.getWriteCV(int cv, int val, int mode)
CanMessage	CbusAddress.makeMessage()

Methods in jmri.jmrix.can.cbus with parameters of type CanMessage

int	CbusEventFilterFrame.filter(CanMessage m)
boolean	CbusEventFilter.filter(CanMessage m) Filter an event, based on previous settings.
static int	CbusMessage.getDataLength(CanMessage m)
static int	CbusMessage.getEvent(CanMessage m)
static int	CbusMessage.getEventType(CanMessage m)
static int	CbusMessage.getId(CanMessage m)
static int	CbusMessage.getNodeNumber(CanMessage m)
static int	CbusMessage.getOpcode(CanMessage m)
static int	CbusMessage.getPri(CanMessage m)
static boolean	CbusMessage.isEvent(CanMessage m)
static boolean	CbusMessage.isRequestTrackOff(CanMessage m)
static boolean	CbusMessage.isRequestTrackOn(CanMessage m)
void	CbusTurnout.message(CanMessage f)
void	CbusThrottleManager.message(CanMessage m)
void	CbusSensorManager.message(CanMessage l)
void	CbusSensor.message(CanMessage f) Track layout status from messages being sent to CAN
void	CbusProgrammer.message(CanMessage m)
void	CbusPowerManager.message(CanMessage m)
void	CbusDccProgrammer.message(CanMessage m)
void	CbusCommandStation.message(CanMessage m)
static void	CbusMessage.setId(CanMessage m, int id)
static void	CbusMessage.setPri(CanMessage m, int pri)
static String	CbusMessage.toAddress(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.cbus.swing.configtool

Methods in jmri.jmrix.can.cbus.swing.configtool with parameters of type CanMessage

void	ConfigToolPane.message(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.cbus.swing.console

Methods in jmri.jmrix.can.cbus.swing.console with parameters of type CanMessage

void	CbusConsoleFrame.message(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.cbus.swing.eventtable

Methods in jmri.jmrix.can.cbus.swing.eventtable with parameters of type CanMessage

void	CbusEventTableDataModel.message(CanMessage m) *** Capture node and event and add to table

Uses of CanMessage in jmri.jmrix.can.cbus.swing.nodeconfig

Methods in jmri.jmrix.can.cbus.swing.nodeconfig with parameters of type CanMessage

void	NodeConfigToolPane.message(CanMessage m)

Uses of CanMessage in jmri.jmrix.can.swing.monitor

Methods in jmri.jmrix.can.swing.monitor with parameters of type CanMessage

void	MonitorFrame.message(CanMessage l)

Uses of CanMessage in jmri.jmrix.can.swing.send

Methods in jmri.jmrix.can.swing.send with parameters of type CanMessage

void	CanSendFrame.message(CanMessage m) Don't pay attention to messages

Uses of CanMessage in jmri.jmrix.openlcb

Methods in jmri.jmrix.openlcb that return CanMessage

CanMessage

OlcbAddress.makeMessage()

Methods in jmri.jmrix.openlcb with parameters of type CanMessage

void	OlcbTurnout.message(CanMessage f)
void	OlcbSensorManager.message(CanMessage l)
void	OlcbSensor.message(CanMessage f) Track layout status from messages being sent to CAN

Uses of CanMessage in jmri.jmrix.openlcb.swing.monitor

Methods in jmri.jmrix.openlcb.swing.monitor with parameters of type CanMessage

void	MonitorFrame.message(CanMessage l)

Uses of CanMessage in jmri.jmrix.openlcb.swing.send

Methods in jmri.jmrix.openlcb.swing.send with parameters of type CanMessage

void	OpenLcbCanSendFrame.message(CanMessage m) Don't pay attention to messages